SMA boards

Boards with an SMA connector can be used in several ways. The primary method for drones is mounting the board with the connector facing up, and the antenna screws onto the connector. The second method involves mounting the board so that the connector passes through the device's housing, and the antenna connects via a cable. In both cases, the SMA connector serves as the primary mounting point for the board. All this boards have antenna bias tee and can be used only with active GNSS antennas.

Incase 40x20 USB

Photo: INCASE_40x20_USB_SMA_ELT0078.jpg. Interfaces: USB type A connector, 6-pin JST SH connector with power and UART at TTL levels, and I2C. SPI can be used instead of UART and I2C (to enable SPI, short the D_SEL contacts). A 621 battery is used. Weight: 9 grams.

ELT0078 — NEO-M8P-2 receiver

Incase 40x20 miniUSB

It differs from Incase 40x20 USB by using miniUSB instead of USB type A.

ELT0077 — NEO-M8P-2 receiver

Incase 38x22 miniUSB

Interfaces: miniUSB connector, 12-pin JST SH connector with power, two UARTs at TTL levels, and I2C. SPI can be used instead of one UART and I2C (to enable SPI, short the D_SEL contacts). A supercapacitor is used. An ultra-low noise stabilizer is used for protection against impulse noise. Weight: 9 grams.

ELT0087 — ZED-F9P receiver

ELT0088 — ZED-F9T-00B receiver

ELT0091 — ZED-F9P receiver with ELT0014 antenna

ELT0098 — ZED-F9H receiver

ELT0141 — ZED-F9T-10B receiver

Incase 35x23

It differs from Incase 38x22 miniUSB by using 14 contacts instead of the JST SH and miniUSB connectors.

ELT0092 — ZED-F9P receiver

ELT0094 — ZED-F9T-00B receiver

ELT0096 — ZED-F9H receiver

ELT0144 — ZED-F9T-10B receiver

Incase 26x16 JST SH

Interfaces: 6-pin JST SH connector with power, UART at TTL levels, and I2C. A supercapacitor is used. Weight: 7 grams.

ELT0023 — MAX-M8Q receiver. For use with an active antenna only.

ELT0151 — MAX-M10S receiver

Incase 41x30 miniUSB RS232

The only board with an RS-232 interface. For additional M3 screw mounting, there is a hole in the corner. Interfaces: miniUSB connector, 8 contacts: power, UART at TTL levels, and RS-232. One of the two boards without a battery and supercapacitor.

ELT0025 — LEA-6T receiver. The board is outdated and no longer produced.

ELT0026 — LEA-M8S receiver. For use with an active antenna only. The board is outdated and no longer produced.

ELT0029 — LEA-M8T receiver. For use with an active antenna only.

Incase 33x31 M8F

A special board for M8F. For additional M3 screw mounting, there are two holes. Interfaces: miniUSB connector, 12 contacts: power, UART at TTL levels, and I2C, plus many additional contacts for synchronization with external generators (specific to M8F). SPI can be used instead of UART and I2C (to enable SPI, short the D_SEL contacts). One of the two boards without a battery and supercapacitor.

ELT0030 — LEA-M8F receiver.

Incase 40x18 miniUSB

Interfaces: miniUSB connector, 6 contacts: power, UART at TTL levels, and I2C. A 621 battery is used. Weight: 8.1 grams.

ELT0031 — NEO-M8N receiver. The board is outdated and no longer produced.

ELT0032 — NEO-M8T receiver

ELT0101 — NEO-M9N receiver

Incase 40x18 JST SH

Interfaces: 6-pin JST SH connector with power, UART at TTL levels, and I2C, separate 4-pin JST SH connector for USB. A supercapacitor is used. Weight: 8.1 grams.

ELT0035 — NEO-M8N receiver.

Incase 36x19

Interfaces: 12 contacts: power, USB, UART at TTL levels, and I2C. SPI can be used instead of UART and I2C (to enable SPI, short the D_SEL contacts). A 621 battery is used. Weight: 6.8 grams.

ELT0065 — NEO-M8T receiver

ELT0066 — NEO-M8L ADR receiver. For use with an active antenna only.

ELT0067 — NEO-M8U UDR receiver. For use with an active antenna only. The board is outdated and no longer produced.

ELT0068 — NEO-M8N receiver

ELT0165 — NEO-M9V ADR+UDR receiver

Incase 36x30 miniUSB

Interfaces: miniUSB and 14 contacts: power, two UARTs at TTL levels, and I2C. SPI can be used instead of UART and I2C (to enable SPI, short the D_SEL contacts). A supercapacitor is used. Weight: 11 grams.

ELT0112 — ZED-F9P receiver

ELT0113 — ZED-F9T-00B receiver

ELT0117 — ZED-F9R ADR receiver

ELT0145 — ZED-F9T-10B receiver

Square 30

This board is used in smartwatches. Mounting: four screws in the corners. Interfaces: 6 contacts: power, UART at TTL levels, and I2C. A supercapacitor is used. Weight: 6.8 grams.

ELT0107 — NEO-M9N receiver

ELT0108 — NEO-M9N receiver with ELT0014 antenna

ELT0125 — NEO-M8U UDR receiver. For use with an active antenna only. The board is outdated and no longer produced.

© Eltehs SIA 2023